Automated Doors & Gates Ltd

Automatic Door or Barrier Not Working? What Your Site Team Should Do Before Calling an Engineer

When an automatic door, gate or barrier stops working, the pressure is on straight away. Staff can’t get in, patients are waiting, deliveries are stuck at the entrance. The temptation is to try to fix it there and then. This guide sets out what a site team can safely do first, what they should never do, and when it’s time to call us.

First: make it safe

Before anything else, think about the people using the entrance.

  • If the door, gate or barrier is moving in an unusual way, stopping and starting, or hitting things, take it out of use if you can do so safely.
  • Put up a clear notice and direct people to another safe entrance if you have one.
  • Keep people, and especially children, away from moving parts and from the closing edge.

Simple checks your team can make

These checks don’t involve opening covers, touching wiring or adjusting anything. If one of them solves the problem, still make a note of it in your site log.

Has it been switched off or set to the wrong mode? Many automatic doors have a mode switch (for example open, automatic, exit only or locked). Cleaners, keyholders or out-of-hours staff sometimes change it. Check it’s set as normal.

Is anything in the way? Mats that have curled or slipped, leaves and grit in a sliding door’s floor track, bins, A-boards or deliveries near the door can stop it closing or keep its sensors triggered. For gates and barriers, check nothing is parked or left in the path of the gate or arm.

Are the sensors or photocells blocked? Stickers, posters, condensation or a parked vehicle can block the sensors that make a door, gate or barrier open and stop safely. Clear anything you can see in front of them, but don’t move, clean inside or adjust the sensors themselves.

Is it an access control fault? If the door or barrier works from the exit side but not from a keypad, fob reader or intercom, the fault may be in the access control rather than the door or barrier itself. Tell us that when you call, as it helps the engineer come prepared.

What your team should never do

  • Don’t remove covers, open control boxes or touch wiring.
  • Don’t wedge a door open, tape over a sensor or leave a barrier arm raised as a workaround.
  • Don’t bypass or disconnect safety devices such as photocells, safety edges or sensors.
  • Don’t keep using a door, gate or barrier that is behaving unusually just to keep traffic moving.

Safety devices are there to stop people being trapped or struck. A quick workaround can turn a fault into an accident.

When to call an engineer

Call us on 01206 591001 if the simple checks don’t sort it out, or straight away if:

  • the door, gate or barrier is moving erratically, making grinding or banging noises, or not stopping when something is in the way
  • there’s visible damage, for example after a vehicle has hit a barrier or gate
  • it won’t close, so your building or site can’t be secured
  • the same fault keeps coming back

When you call, it helps to tell us what the equipment is, what it’s doing (or not doing), when it started, and anything that changed just before, such as a power cut, bad weather or a vehicle strike.

Fewer breakdowns in the first place

Many faults that stop an entrance in its tracks start as small signs of wear: a door that’s slower than it used to be, a barrier arm that judders, a gate that stops short. Regular servicing picks these up on a planned visit, at a time that suits you, rather than in the middle of a busy day.

Servicing also helps you meet your legal duty under PUWER 1998 and the Workplace Regulations 1992 to keep automatic doors and gates maintained, in line with BS EN 16005 for doors and BS EN 12453 for gates. Keep each service report with your site log so you have a clear record of what has been done and when.

About Automated Doors & Gates Ltd

We repair, service and maintain automatic doors, electric gates, barriers, bollards and access control for schools, GP surgeries, care homes and businesses across north Essex and south Suffolk, from our base in Lawford, near Manningtree. We’re an ADIA member (The Automatic Door Installation Association) and a Gate Safe Aware Installer (certificate no. 2583), and we also install new systems.

To report a fault or book a service, call 01206 591001 or email service@a-d-g.co.uk.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top